Sterling Silver Crescent and Bead Earrings
Supplies Desired
3" 4 x 1 mm sterling silver rectangle wire
Twenty-one particular 'Λ* head pins
Two turquoise disc beads
Just one Vi* one.7 mm black hollow rubber tube
Two sterling silver ear wires
What guidance would you provide a starting artist?
“Do That which you appreciate. Explore different media. Promote on the selective, constrained, foundation at the outset to check out what works or what does not work for you before you leap into A significant outlay of money and effort.*
-Sally J. Phillips Jewellery Designer
Equipment Wanted
Ruler
Marker
Jeweler's observed or tin snips Protection Eyeglasses Tricky, flat area Awl
Hammer /is" drill little bit
Hand-held rotary Software, flex shaft, or drill push File
Fine grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Round nose pliers
1.Use the ruler to measure and mark two 1 Vi’ pieces of 4 x 1 mm rectangle sterling silver wire.
2Using a jeweler's saw or tin snips, cut the 4 x 1 mm rectangle sterling silver wire into two one Vi’ lengths.
three.File each end of the 1Vi" rectangle wire pieces to remove any burs or rough edges.
If desired, You should use the file to round the ends of the rectangle wire pieces. Use a fine grit sanding pad to go over the area in which you have submitted to sleek the sides and take away any file marks.
four.Make use of the ruler to evaluate and mark /*." from one particular conclude in the 1 Vi’ pieces of rectangle wire and location a mark in the center from the wire. This is where you will drill the holes to slip The pinnacle pins as a result of.
five.Set on your own basic safety glasses!!! Spot the 1 Vi" rectangle wire pieces onto a tough, flat area. Position The purpose on the awl within the mark which you manufactured Vm,' from a single stop from the rectangle wire pieces, and firmly strike once on the best of your awl that has a hammer. This is likely to make a pilot gap for drilling holes to the rectangle wire.
Sterling Silver Crescent and Bead Earrings
Chapter 5
6.Employing a /is" drill little bit. drill holes into one particular conclude in the rectangle wire pieces with a handheld rotary tool, flex shaft, or drill push (when even now donning your security glasses!).
seven.Make use of the file or wonderful grit sanding pad to eradicate any burs or rough edges remaining from drilling holes into your rectangle wire items.
8.Curve each 1W pieces of rectangle wire right into a “C" form utilizing a ring mandrel and rawhide mallet. If you do not have a hoop mandrel and rawhide mallet, use two set of chain nose pliers. Holding 1 pair of pliers in Each individual hand, grasp Just about every conclude in the 1 Vi* rectangle wire piece While using the pliers and Carefully bend the rectangle wire into a “C* shape. Compare both equally on the C-shaped rectangle wire pieces and regulate the curves so that they're equivalent in si2e. Set these apart.
nine.Use the ruler to measure and mark the rubber tube into 4 equal pieces measuring Vm’ Each individual. Use scissors to chop the rubber tube.
10.Place the turquoise disc bead on to The top pin and include one V·' bit of the rubber tube, spot the head pin in the gap inside the C-shaped rectangle wire, and afterwards incorporate the other V«" bit of rubber tube.
thirteen. Hold The pinnacle pin Along with the bead, rubber tube, as well as the rectangle wire on it in one hand Along with the wire that you just bent pointing toward you. Utilizing the round nose pliers, grip the end of The pinnacle pin wire which is pointing toward you and roll it clear of you (think about turning the ignition important to get started on your vehicle). Release the pliers from The pinnacle pin wire.
At this time, the opening in the loop at the highest of The top pin wire Mens Ring should however be huge enough to slide the ear wire on. After you increase the ear wire, make use of the round nose pliers to grasp the loop of The pinnacle pin wire and roll it closed. You may use the round nose or chain nose pliers to adjust The form of the loop at the best of The top pin if you have to.
11. Make use of the ruler to measure and mark /(.’ mens ring higher than the very best bit of the hollow rubber tube. Together with the wire cutters or tin snips, Reduce The pinnacle pin wire Yu.’ over the best on Mens Ring the hollow rubber tube.
12. Make use of the chain nose pliers to bend the head mens ring pin wire close to the top with the rubber tube at a ninety-degree angle.
fourteen. Repeat Mens Ring these measures for the 2nd earring.